Recently, plastic radiators have also attracted people's attention. Materials with good thermal conductivity are usually materials with good electrical conductivity. In turn, plastics with poor electrical conductivity must have poor thermal conductivity. This is inevitable. So obviously metal is better than plastic. In fact, it is the same. So, isn't plastic enough to be used as a radiator? Not so!
Recently, a variety of thermal conductive plastics have been developed internationally, and most of the materials are based on engineering plastics and general-purpose plastics, such as PP, ABS, PC, PA, LCP, PPS, PEEK, and the like. The plastic is then filled with certain metal oxide powder, carbon, fiber or ceramic powder. For example, polyphenylene sulfide (PPS) can be mixed with large-particle magnesium oxide (40-325 mesh) to form an insulating heat-conductive plastic. Typical thermal conductivity ranges from 1-20 W/mK and some grades can reach 100 W/mK. This value is about 5-100 times that of traditional plastics. The thermal conductivity of general plastics is only 0.2 W/mK. However, if too much metal powder is added in order to obtain high thermal conductivity, it becomes conductive. It can not be applied in some occasions. The performance of some thermal conductive plastics from Coolploy in the United States is as follows.
E4505 (PC): Thermal Conductivity 10w/mk Thermal Conductive Applications: Housing and Radiator
D5108 (PPS): Thermal Conductivity 10w/mk Thermal Insulation Application: Board/Chip
D5506 (LCP): Thermal Conductivity 10w/mk Thermal Insulation Application: Board/Chip
D8102 (TPE): Thermal Conductivity 3w/mk Thermal Insulation Application: Interface
E5101 (PPS): Thermal conductivity 20w/mk Thermal conduction application: heat sink.
So why can thermal plastics be made into heat sinks? Can its heat dissipation be comparable to traditional aluminum heat sinks? It's ok, even better! Can you believe it?
We know that any heat sink, in addition to being able to quickly transfer heat from the heat source to the surface of the heat sink, still relies on convection and radiation to dissipate heat into the air. The high thermal conductivity solves the problem of fast heat transfer, and the heat dissipation is mainly determined by the heat dissipation area, shape, natural convection and heat radiation, which are almost independent of the thermal conductivity of the material. So as long as there is a certain heat transfer capacity, the plastic radiator can still be a good radiator!
Generally speaking, if the distance from the heat source to the surface of the heat sink is less than 5 mm, as long as the thermal conductivity is greater than 5, the heat dissipation is dominated by convection, and at this time, conduction heat dissipation has no effect. This can be seen from the curve below.
Figure 1. Relationship between thermal conductivity and conduction convection heat dissipation
The relationship between thermal conductivity and conduction convection heat dissipation is given in Figure 1. In the figure, the abscissa is the thermal conductivity and the ordinate is the temperature difference between the heat source and the environment. The curves for the various colors are the distance between the heat source and the surface of the heat sink. If the distance is less than 5mm (green curve), as long as the thermal conductivity is greater than 5, its heat dissipation capacity is completely determined by convection. The smaller the temperature difference and the smaller the distance, the less important the thermal conductivity is.
And for an ideal good heat sink, about 70% of the heat is convective heat, and 30% of the heat is radiated by radiation.
The heat dissipation capability of the heat-conductive plastic is not inferior. Below are the thermal emissivity of various materials.
So it can be said that if two radiators of the same shape are identical, one is made of aluminum and the other is made of heat-conductive plastic. If the radiator made of aluminum is not blackened, its heat dissipation capability is not comparable to that of black thermal plastic. The heat sink! Because the convection heat of the two is the same, and the radiation heat is better with plastic!